Super Battle Golf
Install with App

Details

Latest version
1.0.0
Last Updated
First Uploaded
Downloads
65
Likes
0
Size
22KB
Dependants

SliderSens

Adds a second decimal place to the sensitivity sliders in Super Battle Golf. Client-side: only you need it.

Version 1.0.0, tested on the game files of 24 October 2026 with BepInEx 5.4.23.5.

What it does

Added

  • The four sensitivity sliders (mouse, mouse aim, controller and controller aim) go in steps of 0.01 and show two decimal places: 1.23x instead of 1.2x.
  • The value you see is exactly the value the game uses and saves. In the game, the label is rounded and the setting is wherever the slider ended up.
  • Arrow keys: with the mouse pointer over a sensitivity slider, Left and Right move it by 0.01. Hold Shift for 0.1.
  • Gamepad: on a sensitivity slider, Left and Right move it by 0.01. Hold either trigger for 0.1.
  • Settings in BepInEx/config/com.slidersens.cfg to turn the arrow keys or the gamepad steps off. See Settings.

Changed

  • Nothing else about the sliders:
    • Same range, 0.10x to 5.00x, and the same default, 1.00x, in the middle of the slider.
    • Same feel when you drag: the left half still goes from 0.1x to 1.0x and the right half from 1.0x to 5.0x.
    • With mouse and keyboard, the game still snaps anything from 0.91x to 1.39x to 1.00x.
  • A value near 1.0x set with a gamepad isn't reset when the game sets up its settings menu.

Install

You need BepInEx 5 (BepInEx-BepInExPack-5.4.2305, installed for you by mod managers).

  • With r2modman or another Thunderstore mod manager: install SliderSens.
  • By hand: copy SliderSens.dll into Super Battle Golf/BepInEx/plugins/SliderSens/.

Only you need the mod. It works in any lobby, whoever hosts, and other players see no difference.

Usage

  1. Open Settings > Controls. The sensitivity sliders are under Camera, for Mouse and Keyboard and for Controller.
  2. Drag a slider close to the value you want.
  3. Fine-tune it: point at the slider and press Left or Right (Shift for 0.1), or on a gamepad press Left or Right (a trigger for 0.1).
  4. Close the settings. The game saves the value, so it's still there after a restart.

How far each input moves a slider:

Input Step
Left or Right 0.01
Shift + Left or Right 0.1
Gamepad: Left or Right 0.01
Gamepad: either trigger + Left or Right 0.1

Holding a key or direction repeats it: once, then after 0.4 seconds ten times a second.

Settings

Edit BepInEx/config/com.slidersens.cfg (in r2modman: Config editor), then restart the game.

Setting Default What it does
General.Enabled true false turns the mod off and gives you the game's own sliders, with one decimal place.
Keyboard.FineAdjust true false turns the arrow keys off: they then do what they do in the game.
Gamepad.FineAdjust true false turns the gamepad steps off: Left and Right move in the game's own steps (0.09 below 1.0x, 0.4 above).

Good to know

  • Tested in game with mouse and keyboard and with a controller; not yet in VR or alongside the other mods listed below. If something doesn't work as described, please send BepInEx/LogOutput.log, and a screenshot if a label looks wrong.
  • The snap to 1.00x stays. With mouse and keyboard, the game turns anything from 0.91x to 1.39x into 1.00x, and SliderSens keeps that. The arrow keys jump straight across: from 0.90x, one press up gives 1.00x and the next 1.40x. To set a value in between, use a gamepad, and don't move that slider with the mouse afterwards.
  • Dragging is coarser than 0.01 above 1.0x, because the slider moves a pixel at a time. Drag close, then use the arrow keys or the gamepad.
  • While the pointer is over a sensitivity slider, Left and Right move that slider and nothing else.
  • Removing the mod is safe: your values stay, shown with one decimal place. The game itself turns a value from 0.91x to just under 1.4x back into 1.0x when it next sets up the settings with mouse and keyboard.
  • After a game update, if the mod can't apply itself fully, it switches itself off instead of half-working. The game then keeps its own sliders, and BepInEx/LogOutput.log shows [FAILED]. If only the arrow keys or the gamepad steps can't apply, just that part switches off.

Compatibility

  • None of MaxFOVSlider, BigLobby, VCTextLobby or SBGVR changes the sensitivity sliders (checked in their code; not yet tested together in game).
  • In VR, click a slider before using the arrow keys on it.
  • Client-side only: it changes your own settings, and sends nothing over the network.

Contact

Questions and bug reports: lmkHenlo, [email protected]. Please attach BepInEx/LogOutput.log, and a screenshot if a label looks wrong.

License

MIT © 2026 lmkHenlo

Thunderstore development is made possible with ads. Please consider making an exception to your adblock.